I wonder if my system is good or bad. My server needs 0.1kWh.
You must log in or register to comment.
Pulling around 200W on average.
- 100W for the server. Xeon E3-1231v3 with 8 spinning disks + HBA, couple of sata SSD’s
- ~80W for mths unifi PoE 48 Pro switch. Most of this is PoE power for half a dozen cameras, downstream switches and AP’s, and a couple of raspberry pi’s
- ~20W for protectli vault running Opnsense
- Total usage measured via Eaton UPS
- Subsidised during the day with solar power (Enphase)
- Tracked in home assistant
Mate, kWh is a measure of electricity volume, like gallons is to liquid. Also, 100 watt hours would be a much more sensical way to say the same thing. What you’ve said in the title is like saying your server uses 1 gallon of water. It’s meaningless without a unit of time. Watts is a measure of current flow (pun intended), similar to a measurement like gallons per minute.
For example, if your server uses 100 watts for an hour it has used 100 watt hours of electricity. If your server uses 100 watts for 100 hours it has used 10000 watts of electricity, aka 10kwh.
My NAS uses about 60 watts at idle, and near 100w when it’s working on something. I use an old laptop for a plex server, it probably uses like 50 watts at idle and like 150 or 200 when streaming a 4k movie, I haven’t checked tbh. I did just acquire a BEEFY network switch that’s going to use 120 watts 24/7 though, so that’ll hurt the pocket book for sure. Soon all of my servers should be in the same place, with that network switch, so I’ll know exactly how much power it’s using.
My server rack has
- 3x Dell R730
- 1x Dell R720
- 2x Cisco Catalyst 3750x (IP Routing license)
- 2x Netgear M4300-12x12f
- 1x Unifi USW-48-Pro
- 1x USW-Agg
- 3x Framework 11th Gen (future cluster)
- 1x Protectli FE4B
All together that draws… 0.1 kWh… in 0.327s.
In real time terms, measured at the UPS, I have a running stable state load of 900-1100w depending on what I have at load. I call it my computationally efficient space heater because it generates more heat than is required for my apartment in winter except for the coldest of days. It has a dedicated 120v 15A circuit
17W for an N100 system with 4 HDD’s
0.1kWh per hour? Day? Month?
What’s in your system?
Computer with gpu and 50TB drives. I will measure the computer on its own in the enxt couple of days to see where the power consumption comes from
You are misunderstanding the confusion, Kwh is an absolute measurement of an amount of power, not a rate of power usage. It’s like being asked how fast your car can go and answering it can go 500 miles. 500 miles per hour? Per day? Per tank? It doesn’t make sense as an answer.
Does your computer use 100 watt hours per hour? Translating to an average of 100 watts power usage? Or 100 watt hours per day maybe meaning an average power use of about 4 watts? One of those is certainly more likely but both are possible depending on your application and load.
You’re adding to the confusion.
kWh (as in kW*h) and not kW/h is for measurement of energy.
Watt is for measurement of power.They said kilawatt hours per how, not kilawatts per hour.
kWh/h = kW
The h can be cancelled, resulting in kW. They’re technically right, but kWh/h shouldn’t ever be used haha.
Lol thank you, I knew that I don’t know why I wrote it that way, in my defense it was like 4 in the morning.
Which GPU? How many drives?
Put a kill-o-watt meter on it and see what it says for consumption.
Do you mean 0.1kWh per hour, so 0.1kW or 100W?
My N100 server needs about 11W.
To my understanding 0.1kWh means 0.1 kW per hour.
It’s the other way around. 0.1 kWh means 0.1 kW times 1 h. So if your device draws 0.1 kW (100 W) of power for an hour, it consumes 0.1 kWh of energy. If your
devicefactory draws 360 000 W for a second, it consumes the same amount of 0.1 kWh of energy.Thank you for explaining it.
My computer uses 1kwh per hour.
It does not yet make sense to me. It just feels wrong. I understand that you may normalize 4W in 15 minutes to 16Wh because it would use 16W per hour if it would run that long.
Why can’t you simply assume that I mean 1kWh per hour when I say 1kWh? And not 1kWh per 15 minutes.
kWh is a unit of power consumed. It doesn’t say anything about time and you can’t assume any time period. That wouldn’t make any sense. If you want to say how much power a device consumes, just state how many watts (W) it draws.
Thanks!
0.1kWh per hour can be written as 0.1kWh/h, which is the same as 0.1kW.
Thanks. Hence, in the future I can say that it uses 0.1kW?
Yes. Or 100W.
If this was over an hour, yes. Though you’d typically state it as 100W ;)
Idle: 30 Watts
Starting all docker containers after reboot: 140 Watts
It needs around 28 kWh per month.
My 10 year old ITX NAS build with 4 HDDs used 40W at idle. Just upgraded to an Aoostart WTR Pro with the same 4 HDDs, uses 28W at idle. My power bill currently averages around US$0.13/kWh.
last I checked with a kill-a-watt I was drawing an average of 2.5kWh after a week of monitoring my whole rack. that was about three years ago and the following was running in my rack.
- r610 dual 1kw PSU
- homebuilt server Gigabyte 750w PSU
- homebuilt Asus gaming rig 650w PSU
- homebuilt Asus retro(xp) gaming/testing rig 350w PSU
- HP laptop as dev env/warmsite ~ 200w PSU
- Amcrest NVR 80w (I guess?)
- HP T610 65w PSU
- Terramaster F5-422 90w PSU
- TP-Link TL-SG2424P 180w PSU
- Brocade ICX6610-48P-E dual dual 1kw PSU
- Misc routers, rpis, poe aps, modems(cable & 5G) ~ 700w combined (cameras not included, brocade powers them directly)
I also have two battery systems split between high priority and low priority infrastructure.
I was drawing an average of 2.5kWh after a week of monitoring my whole rack
That doesn’t seem right; that’s only ~18W. Each one of those systems alone will exceed that at idle running 24/7. I’d expect 1-2 orders of magnitude more.
IDK, after a week of runtime it told me 2.5kwh average. could be average per hour?
Highest power bill I ever saw was summer of 2022. $1800. temps outside were into to 110-120 range and was the hottest ever here.
maybe I’ll hook it back up, but I’ve got different (newer) hardware now.
Ugh, I need to get off my ass and install a rack and some fiber drops to finalize my network buildout.
would love to add more fiber to my diet! if I had the time and money. next four years is going to get pricy so I’m solidifying my stack now with backup hardware and planning for failures.
the brocade is running my pvt lan since it’s the most important. physically cut off public access. just upgraded most my servers to use 10gbe and would love to run fiber to my office about 60-70 feet away.
the brocade I’m using was unlocked by the eBay seller I got it from, so it can theoretically transfer up to 40g. would be great for my AI rig I keep in the office.
I’m idling at 120W with eight drives, but I’m currently looking into how to lower it.
I think at max 200w? It runs a collection of fedi/self service stuff.
I also run a pi with a couple of apps on a pi 3 that sips power.
It’s a legitimate issue because it’s 50+ cents per killowat hour where I live so power is very expensive…
Holy shit. I’m paying less than 10c per kwh even in the “high usage” tier.
I wish that was ours…
80-100 watts at idle which is most of the time. Two OS drives, two fast drives, two spinners, lots of networking and always syncing with the rest of the cluster.
My servers (an old desktop overstuffed with drives and an old dell laptop), networking gear and a 50 gal aquarium all run on the same outlet. As long as the aquarium heater is off, the outlet pulls about 200 watts. The aquarium heater spikes that to 400 watts when it kicks in.
For two servers (one with a lot of spinning rust), two switches, and a few other miscellaneous network appliances. My server rack averages around 600-650W. During periods of high demand (nightly backups, for instance), that can peak at around 750W.
Wow, that sounds like I have rookie numbers
the boxes i have running 24/7 use about 20w max each, and about half that at idle or ‘normal’ loads.
