I’m thinking about upgrading my W-Fi and I was curious what wireless access points (WAP) people are using. I’m currently using a Netgear R7800 running OpenWRT.
You must log in or register to comment.
Went all in with UniFi some time back. No regrets.
Currently running a few U6s. No real motivation to upgrade to U7s.
+1 on this. Though i picked up 2 u7’s. VLAN support, easy to maintain and lets face it, superior function from most retail APs. If you’re a power user, this is the way.
While expensive, UniFi hardware is just a huge step beyond the rest of the consumer market.
I’ve had literally 10x the range (5x vs 50m), in congested environments, compared to ‘gaming’ hardware. I actually did a side by side to test. I was shocked at the difference.
The bridging function is also a life saver. 2 LR units can get a reliable signal between each other, at ridiculous ranges.
I used to use R7800s. Then switched to UAP AC Pro / U6 Pro. Today just tested the OpenWrt One.
- The R7800 (on OpenWrt) is superb, fast, reliable. Can’t say anything bad about it. One of the most successful wireless platforms I’ve used. Probably the best implementation of this chipset too.
- The UAP AC Pro / U6 Pro perform better than the R7800. They have significantly better radio performance. The range is longer, coverage is uniform, performance is more consistent within the covered area. Adding a local Unifi controller (can be done in Docker) adds some nice wireless and management features like band steering. They don’t work well for bridging / mesh though. I had to run a bridge at some point and a set of Unifi had significant latency spikes, making it bad for gaming and other low-latency applications. A R7800-to-R7800 wireless bridge in the same application was superb with consistently low latency. Unifi can be had for cheaper second hand. Lots of corpos have them and old units get dumped upon upgrades.
- The OpenWrt One, through my very limited testing shows great performance in good radio conditions. Once you put some obstacles for the signal, performance degrades much quicker than Unifi U6 Pro. In a particular test where the Unifi achieved 50Mbps, the OpenWrt One did 1.5Mbps. I haven’t compared it to an R7800. I don’t know if it would perform any better with different antennas.
Before that I’ve used R7000, WZR-300HP, WL-500g, WRT54G/L, among others, but none of these are relevant today. :D
Unifi has amazing radio performance, but the software is yucky. and they “recently” (last year?) had a backwards-incompatible update of the controller software which I still didn’t get to migrate.
I’m probably on it already on account that my docker service pulls the latest image on restart. Something I should change.
Mine stopped updating at some point and I’ve read that this one has been discontinued, please migrate to the new one.
Edit: link for reference https://docs.linuxserver.io/deprecated_images/docker-unifi-controller/
Shit. Thank you.
Omada APs, various versions. Really happy with them, their WiFi is great and unlike Ubiquity they also work without the controller as independent devices.
Last I tried a ubiquity AP (2019 or 2020) It could operate independently of a controller with limited features.
Fritzbox boxes.
They tick all the checkboxes
- good standards support (including dect protocol if you want to have an ip phone or even iot protocols)
- fast wifi speeds
- cheap (at least for the second hand in ebay)
- super stable, never had a problem with them in 5 years or more
- fast roaming support out of the box
It is a well known brand in Germany but pretty unknown outside that country. Honestly it is the best bang for buck I was able to get.
Honestly, I would spend 10 minutes checking on them
I really like them but they do have two downsides for “more advanced” users (or at least for me) - it is a home device as after all.
- No support for VLAN or VLAN tagging - you can set up you WiFi and a guest WiFi. You can also map the guest network to an Ethernet port. But that’s about it.
- There is no way to change the DNS suffix (*. fritz.box) to another value - I do own a domain that I use for the local services on my home server, etc. which then allows for Let’s Encrypt certificates, but I cannot use it “out of the box”.
If you’re an advanced user, there’s plenty of ways around that, though. I just wished that these two thing were to exist in the firmware to have less work with my home infrastructure.
Totally agree with the first point, it is a limitation, and the guest wifi sticking to a eth port is just a patch. One that works but still a patch.
But I don’t see the point of the prefixes. What do you mean? I also have a custom domain and a local dns server y can use the domain even internally. I just simple ignore that…
Yeah, I’m also using a local resolver. But since I had some problems using another DHCP server (which was probably a problem on my end), so I’m current setting some devices in my FRITZ!box to a fixed IP and then enter that in my DNS server. If I could just skip the second part and tell the FRITZ!Box to just resolve printserver.example.com instead of printserver.fritz.box - that’d be nice. Maybe I should do another try with a DHCP server soon.
Ruckus APs with wired backhaul OpnSense box runs the network.
I moved to Rukus from Unifi and the difference is night and day. Unifi does not play nice with Sonos and the firmware is rock solid compared to Unifi.
Unifi. I’ve got a box of APs as ewaste just sitting in the basement. Every so often I would get more ewaste from companies I work with.
I don’t need the most demanding of wifi systems. I hardwire most of my stuff whenever possible. And I have a fairly small home. A single AP on the main floor, 1 AP on the basement. 1 AP in the detached garage.
Most of my wifi devices are iot things on their own vlan.
I wanted cheap and OpenWRT, so I got some GLinet Shadows. It has it’s own GUI, but if you go into Advanced Settings, you get the usual OpenWRT Luci interface.
You can set them up as APs or repeaters, and have failover connections. Pretty versatile and easy to use.
2nd hand Ruckus.
They’re decent quality that you’d see in a commercial / enterprise setting (so PoE), but Ruckus also have their “Unleashed” firmware which removes the need for a WLC.
I have 2 in a mesh at home and easily support many IoT devices, phones, laptops, etc on multiple SSIDs
RT-AX88U it has a ton on high end features
I’m using a couple of TP-Link EAP225 ceiling-mounted PoE access points, and one EAP235-wall wall-mounted one, connected to my old TP-Link Archer C7 router (with the antennas disabled) running OpenWRT.
I’d like to replace the router with something rack-mounted, but haven’t gotten around to it yet.
GL.Inet. OpenWRT at the core, and a solid hardware base to run on.
I love that GL.iNet stuff ships with OpenWRT (or apparently FreeRTOS in the case of the Thread border router I’m eyeing right now), but I wish they would make stuff like ceiling or wall-mounted PoE access points and rack-mountable wired routers. The form-factor is what stops me from choosing them over TP-Link devices that I have to flash OpenWRT onto myself.
I purchases a few Netgear R6220, and of course flashed OpenWRT on all of them!
Great hardware, cheap, and perfectly supported. A few years old, so I could even find them used at an amazing price point.
TP link EAP’s and i run the omada software controller on an existing server. Right now I have 3 AP’s and it’s been a great experience so far compared to running consumer wifi routers before. All are on ethernet too.
Same, I needed to expand my Wi-Fi and was to lazy to run an Ethernet and a power cable across the attic. I settled for two TP-Link EAP and a TP-Link managed switch that also provides PoE. You can run all three devices stand alone, but Omada is also quite nice - you can run it without using their cloud on your home server and even connect their app to your local controller.
I use the tp-link EAP615 wall Apps, they are great and run OpenWRT like a champ.
I bought a Grandstream GWN7660 last year and it seems pretty good, it replaced a ubiquity WAP that I still have legacy devices connected to.
